Development of 3d printed microdialysis probe for determining glucose concentration in vitro
➤ Gửi thông báo lỗi ⚠️ Báo cáo tài liệu vi phạmNội dung chi tiết: Development of 3d printed microdialysis probe for determining glucose concentration in vitro
Development of 3d printed microdialysis probe for determining glucose concentration in vitro
THAI NGUYEN UNIVERSITYUNIVERSITY OF AGRICULTURE AND FORESTRYDUONG VAN HUYTOPIC TITTLE: DEVELOPMENT OF 3D-PRINTED MICRODIALYSISPROBE FOR DETERMINING GL Development of 3d printed microdialysis probe for determining glucose concentration in vitro LUCOSE CONCENTRATION IN-VITROBACHELOR THESISStudy Mode : Full-timeMajor: Environmental ScienceandManagementFaculty: International TrainingandDevelopment CenterBatch: 2010-2015Thai Nguyen, 22/01/2015Bachelor thesisDOCUMENTATION PAGE WITH ABSTRACTThai Nguyen University of Agriculture and ForestryDegre Development of 3d printed microdialysis probe for determining glucose concentration in vitro e ProgramBachelor of Environmental Science and ManagementStudent nameHuy Van DuongStudent IDDTN 1053110103Thesis TitleDevelopment of 3D-primed MicrodiDevelopment of 3d printed microdialysis probe for determining glucose concentration in vitro
alysis probe for determining glucose concentration In-vitroSupervisors1)Prof. Yuh-Chang Sun, National TsingHua University. Taiwan 2)Assoc. Prof. Dam XTHAI NGUYEN UNIVERSITYUNIVERSITY OF AGRICULTURE AND FORESTRYDUONG VAN HUYTOPIC TITTLE: DEVELOPMENT OF 3D-PRINTED MICRODIALYSISPROBE FOR DETERMINING GL Development of 3d printed microdialysis probe for determining glucose concentration in vitro printing 3D-printed probe by Miicraft 3D printer and assay for testing its efficiency in comparison with the commercial probe. Perfusate, of testing process, was 0.9% NaCI (Sodium Chloride) pumped into the inlet of the probe at different flow rate (0.5pL, IpL. l.5pL. and 2pL). flows past the active Development of 3d printed microdialysis probe for determining glucose concentration in vitro area of the dialysis membrane, and flow out the outlet of the probe. Perfusate, in order of passing by the dialysis membrane, a concentration of glucoDevelopment of 3d printed microdialysis probe for determining glucose concentration in vitro
se is established across the membrane. It facilitates the diffusion of compounds of interest from the extracellular space through the membrane and alsTHAI NGUYEN UNIVERSITYUNIVERSITY OF AGRICULTURE AND FORESTRYDUONG VAN HUYTOPIC TITTLE: DEVELOPMENT OF 3D-PRINTED MICRODIALYSISPROBE FOR DETERMINING GL Development of 3d printed microdialysis probe for determining glucose concentration in vitro from outlet to then analyze and determine the glucose concentration by using fluorescence microplate reader. To come up with final result, the relative recovery was formally calculated by given formula. The desirable efficiency of 3D-printed microdialysis was expected around 70% to 80% compared that Development of 3d printed microdialysis probe for determining glucose concentration in vitro of commercial probe. There were, however, some restrictions as well as limitations found during the conduction such as inaccurate dimension printingDevelopment of 3d printed microdialysis probe for determining glucose concentration in vitro
due toHuy U’dn Duong - K42 AEPiiBachelor thesisthe size of device was ineligible etc. As a result, the identical efficiency of 3D-printed probe was unTHAI NGUYEN UNIVERSITYUNIVERSITY OF AGRICULTURE AND FORESTRYDUONG VAN HUYTOPIC TITTLE: DEVELOPMENT OF 3D-PRINTED MICRODIALYSISPROBE FOR DETERMINING GL Development of 3d printed microdialysis probe for determining glucose concentration in vitro Rs were found at How rale of 0.5pT., Ipl.. I.5pl. and 2.0pI. were around 23.2%, 15.4%, 13.9% and 11.2% respectively in comparison to 42.2%, 35.3% 26.7% and 21.5% of the introduced probe. Although the result was under the expectation, these data have proven that 3D-printed probe possibility could be Development of 3d printed microdialysis probe for determining glucose concentration in vitro touched in the near future, opens a wide application of that device to various fields of study.Key wordsNumber of pageDate of submissionmicrodialysis,Development of 3d printed microdialysis probe for determining glucose concentration in vitro
in-Vilro, 3D-prinled microdialysis, relativerecovery.3522/01/2015Huy Van Duong - K42 AEPiiiBachelor thesisACKNOWLEDGEMENTTHAI NGUYEN UNIVERSITYUNIVERSITY OF AGRICULTURE AND FORESTRYDUONG VAN HUYTOPIC TITTLE: DEVELOPMENT OF 3D-PRINTED MICRODIALYSISPROBE FOR DETERMINING GLTHAI NGUYEN UNIVERSITYUNIVERSITY OF AGRICULTURE AND FORESTRYDUONG VAN HUYTOPIC TITTLE: DEVELOPMENT OF 3D-PRINTED MICRODIALYSISPROBE FOR DETERMINING GLGọi ngay
Chat zalo
Facebook